Klipsch soundbars come with a remote control, but did you know you can also control it with a universal remote? Since universal remote controls can command other devices using specific codes, you can also program it with your Klipsch soundbar.
Our experts explain the methods to program them effortlessly in this guide:
Table of Contents
Programming Universal Remote for Remote Codes Klipsch Soundbar
Here is an extensive protocol that you need to follow to program your remote control for the Klipsch soundbar:
1. Turn the Soundbar on and press the Setup button on the remote control.
2. Hold it for a few seconds until a red LED light turns on.
3. Release the setup key button.
4. Select the device you wish to program your remote and then press the Device key on the remote.
5. If a red light starts to blink, then it will indicate that the device has been selected successfully.
6. Add the code for the selected device in the space given for the code.
7. The light will switch off automatically once you select the correct code for your device.
8. To ensure that you have followed the protocol rightly, use the remote and check Volume, channel, mute, or other function keys.
9. If the remote is working, then it means you have successfully programmed the remote.
Setting the Remote to its Default Settings
1. Turn off the soundbar and remove all the cables and wires from the soundbar.
2. Now turn it on again.
3. Select the Mute button and hold the Volume down key with it.
4. Hold it for a few seconds till a red LED light starts blinking.
5. It will indicate that the Soundbar is reverting to the default settings.
Programming a DirecTV Remote
1. Take the remote control and use AV1/AV2 mode.
2. Select the mute button along with the Select key and hold them for a few seconds.
3. Wait for the LED light to blink two times.
4. Now enter the code in the given space.
5. Add the code 10812
6. Now press the mute + select keys simultaneously for few seconds again and wait for the LED light. It will blink twice.
7. Enter the 3-digit code 993.
8. Press the “Select” button.
9. Set the DirecTV mode and reconnect the wires and cables to the Soundbar.
10. Check if the remote is working correctly or not.
11. Check the function keys and Volume buttons.
Programming Xfinity Remote Control for a Klipsch Soundbar
Two types of Klipsch remotes are usually used for any soundbar. You can program the Xfinity X-1 and XR-15 for your soundbar. Here is the complete manual of programming the Xfinity remote:
1. To start processing with the remote, connect your Soundbar with the device. It should be your device’s primary sound system. Or else, the device will use its inbuilt speakers, and the whole processing will be disturbed.
2. Now turn on the remote and the Soundbar, press the SETUP button for a few seconds.
3. The LED light will start blinking, and it will turn green.
4. It will indicate that it’s the right time to add the relevant code in the given space. Xfinity [1] has its specific codes, which you can find according to the model of the soundbar.
5. After adding the code, check it by pressing volume, mute, or function buttons. If they are working correctly, then you have done the process in the correct method.
Remote Codes for a Klipsch Soundbar
ATT
- 5144
RCA
- 41609
Xfinity
- 30531
DirecTV
- 31609
- 30531
Suddenlink
- 1609
Dish Network
- 2652
Verizon Fios
1050
One for All
- 1609
- 0531
Bright House
- O48
Cox Cable
- 1609
Logitech
- Harmony One
- Harmony 200/300/600/650/700/350
- Ultimate Home
- Harmony One+
- Ultimate Hub
- Home Control
- Smart Control
- Ultimate One
- Smart Keyboard
Hex
- PowerBar Elite
- R-10B
- SB-3
- BTS 2.1
- R-20B
- PowerBase
- SB-120
- PowerBar one
- Torsten
- PowerBar
- SB-1
- CS-30
3-Digit Codes
- 543
- 798
- 691
- 544
- 797
- 687
- 540
- 602
- 545
- 001
4-Digit Codes
- 2076
- 4200
- 1756
- 2056
- 2076
- 4198
- 2066
- 4941
- 1431
- 0765
- 1339
- 3915
5-Digit Codes
- 34200
- 33092
- 44198
- 34198
- 67513
- 23915
- 75002
- 44200
- 23915
- 23092
- 33915
