Marantz Remote Codes & Programming Guide (2026)

Lost the original Marantz remote, or trying to fold your receiver into a single universal remote? This guide gives you the most widely reported Marantz audio codes for the major remote brands, exact programming steps for each, an auto-scan fallback for when a printed code won’t take, and a troubleshooting ladder for the most common failures. Marantz uses dedicated Audio/receiver code sets that are different from its TV codes, so always select your device type as “Audio Receiver” (not TV) before entering anything below.

Marantz Remote Codes by Universal Remote Brand

Start with the most widely compatible codes, then move to brand-specific sets if needed. Code 0216 is the most commonly cited Marantz receiver code and, according to universal-remote code databases, works on the large majority of receivers from the SR5000 era through the current SR8015. Try the alternates in order before resorting to auto-scan.

GE/Jasco 4-Digit Codes

GE and Jasco (the company that manufactures GE-branded universal remotes) use 4-digit codes for audio devices. For Marantz receivers, start with these:

• 0216 — primary GE/Jasco Marantz audio code
• 1216 — alternate, same compatibility
• 1296 — tertiary option

Enter these with the remote set to the AUX or audio device slot. If you own a GE CL-series remote (for example the CL3, CL4, CL5, or CL6), the exact Marantz audio code can differ by remote generation, so check the code sheet that shipped with your remote under the receiver/amplifier category, and use the code-search routine if the 4-digit codes above don’t register. Source: codesforuniversalremotes.com and Alibaba Marantz remote-code buying guide.

RCA Universal Remote Codes

RCA universal remotes maintain a dedicated Marantz Audio code list. RCA remotes vary by model (3-digit vs. 4-digit code length), so consult the code sheet that shipped with your specific RCA remote and look under the Audio / Receiver / Amp heading for Marantz. Because exact RCA-format digits differ by remote generation and we could not confirm a single universal RCA value across every model against an authoritative source, the most reliable path on an RCA remote is to enter your remote’s documented Marantz audio code, and if it doesn’t register, use the auto-scan/code-search method described below. Source: eliztech.com “Marantz Audio codes for RCA” code list.

Philips & Magnavox Remote Codes

Philips and Magnavox (sister brands using shared code databases) publish a separate Marantz Audio code list for their universal remotes. As with RCA, the exact Philips/Magnavox digits depend on your remote model and aren’t a single fixed value we can state with confidence here, so enter the Marantz audio code printed on your remote’s code sheet under the receiver/amplifier category. If no Marantz code is listed or none works, the code-search/auto-scan routine on Philips remotes will cycle through the database for you. Source: eliztech.com “Marantz Audio codes for Philips/Magnavox” code list.

One For All Remote Codes

One For All (URC) remotes have a documented Marantz audio code set. For the receiver/amplifier device key, the codes most commonly listed are:

• 0062
• 0181
• 0004
• 0009

Compatible One For All models include URC1240 (Contour 4), URC1280 (Contour 8), URC3661 (Essential 6), URC7140 (Essence 4), URC7955 (Smart Control 5), and URC7980 (Smart Control 8). Note that these same four digits also appear on some cable-remote Marantz lists, so if a code is rejected on your specific One For All model, confirm the value on your remote’s own code sheet or run its built-in code search rather than assuming the number carries over. Source: eliztech.com One For All Marantz audio code list, last updated March 6, 2026.

Cable & Satellite Provider Codes (Comcast/Xfinity, DIRECTV, DISH, Spectrum)

Most major cable and satellite remotes can drive a Marantz receiver’s basic functions, though advanced features may not map. A practical limitation to know up front: many Marantz receivers (for example the NR1402) use the RC5/RC5x IR protocol, and cable remotes like Comcast’s can send RC5 signals but typically only handle power, volume up/down, and input selection reliably — advanced menu functions often won’t work from a cable remote.

Because provider remotes revise their code databases over time and the exact Marantz digits differ between remote models within the same provider, we’ve stated only the codes we could confirm (Comcast/Xfinity) as specific values. For DIRECTV, DISH, and Spectrum, run the remote’s code-search routine targeting “Audio Receiver / Marantz” rather than entering a guessed number.

Step-by-Step Programming for Each Remote Brand

The exact button labels differ slightly between brands, but the flow is the same: put the remote into programming mode, select the audio/receiver device, enter the code, then test. Use the most-common direct-entry method first.

1. Turn on your Marantz receiver so you can see it respond.
2. On the remote, press and hold the Setup (or Code Search) button until the indicator LED stays lit or blinks, signaling programming mode.
3. Press the device key for the slot you want to use (e.g., AUX, AMP, or Audio), if your remote requires selecting a device.
4. Enter the 4-digit Marantz code — start with 0216 (GE/Jasco), or 0062 / 0181 / 0004 / 0009 (One For All / cable). Press Enter if your remote has one.
5. The LED should blink or turn off to confirm the code was accepted. Test Power and Volume on the receiver.
6. If nothing happens, repeat with the next code in the brand’s list (e.g., 1216, then 1296). If you’re in a multi-Marantz environment, also try toggling the remote’s AMP1/AMP2/AMP3 mode — AMP1 is the default and covers most single-receiver setups.

Auto-Scan / Code Search Method

When no printed code works — or you don’t know your model’s code at all — auto-scan walks through the remote’s entire database one code at a time until the receiver responds. It’s slower (it can take 100+ presses) but it finds codes that direct entry misses. There are two common variants depending on whether your remote accepts manual code entry. Always confirm the precise key sequence in your own remote’s manual, as it varies by brand.

Variant A — Direct entry with testing

1. Turn on the Marantz receiver.
2. Press and hold Setup / Code Search until the LED blinks (programming mode).
3. Enter a 4-digit code (e.g., 0216) and press Enter.
4. Test Power and Volume.
5. If there’s no response, try the next code, or toggle AMP2/AMP3 mode in multi-unit environments where adjacent Marantz gear may interfere.

Variant B — Automatic scan (no code entry)

1. Switch the receiver ON.
2. Press and hold Setup + Power together until the device begins cycling (auto-scan engaged).
3. While it scans, point the remote at the receiver and tap CH+ / CH− to advance through codes until the receiver powers OFF — that’s your match.
4. Immediately press Setup to lock in the found code.
5. Turn the receiver back on and confirm Power, Volume, and Mute all respond.

Source: Alibaba Marantz remote-code buying guide; JustAnswer GE/Marantz programming thread. Exact button names differ between remote brands — check your remote’s manual if the labels above don’t match.

Troubleshooting & Common Issues

Work down this ladder in order — the most common fix is first. Most “no response” problems are a wrong code or a mode/AMP-channel mismatch, not a broken remote.

1. Try the codes in order: 0216, then 1216, then 1296. One of these resolves the majority of cases.
2. Confirm device type: make sure you selected Audio Receiver (not Marantz TV) — the two use different code lists.
3. Toggle AMP mode: switch between AMP1, AMP2, and AMP3. AMP1 is default; the others help when you have multiple Marantz units responding at once.
4. Use auto-scan: if direct entry fails entirely, run the Variant B automatic scan above.
5. Check the receiver state: the receiver must be powered on and in a normal input mode that accepts IR remote input.
6. Replace remote batteries: weak batteries shorten IR range and cause intermittent, hard-to-diagnose failures. Fresh batteries first, then re-test.
7. Consult your receiver’s manual: for the full preset-code list specific to your model (e.g., the SR7015/SR8015 preset PDFs list 4076, 4046, 4047, 4050).

One realistic expectation to set: even with a correct code, a basic cable remote may only give you power, volume, and input switching on an RC5 receiver. For full menu navigation and advanced features, a dedicated universal remote (One For All, GE/Jasco) or a learning remote is the better tool.

Denon & Marantz Code Compatibility Note

Denon and Marantz are sister brands under the same parent company, which leads many owners to assume their remote codes are interchangeable. They generally are not. Both operate their IR at 38 kHz, but the first portion of the hex-code stream identifies the brand and the second portion carries the function bitstream — so a “Denon” code and a “Marantz” code are distinct, and Denon’s own support guidance is that you cannot simply control a Marantz with a Denon remote and expect a full feature match.

That said, some owners report occasional overlap on specific models. Treat trying a Denon code as a last-resort fallback, not a first move: enter the official Marantz codes first, and only try Denon codes if every Marantz option (including auto-scan) has failed. Source: AVS Forum Denon/Marantz IR discussion; Denon support documentation.

Advanced tip: if you have a learning or hex-capable remote, Remote Central hosts a verified set of Pronto-format IR hex codes for the Marantz RC-96SR receiver remote (power, source, component selection, navigation), which you can teach directly to a capable universal remote.

Frequently Asked Questions

What’s the most reliable Marantz remote code for universal remotes?

Code 0216 is the most widely reported code and works across the large majority of Marantz receivers from SR5000 through SR8015, according to universal-remote code databases. Try 1216 or 1296 if 0216 doesn’t work. For newer models (SR7015, SR8015), preset codes 4076, 4046, 4047, and 4050 are documented in the official Marantz preset-code manuals.

Can I use Denon remote codes with my Marantz receiver?

Denon and Marantz use different IR codes — the brand identification in the hex stream differs. Use Marantz codes first. Only try Denon codes as a fallback if official Marantz codes fail; some owners report occasional cross-compatibility on specific models, but it isn’t guaranteed.

How do I program a GE universal remote to control my Marantz receiver?

Press and hold Setup until the LED blinks. Enter code 0216 (or 1216/1296) and press Enter. Test Power and Volume. If there’s no response, try the alternate codes or use auto-scan mode by holding Setup + Power until the device cycles, then press CH+/CH− until the receiver powers off.

Will my Comcast/Xfinity remote work with my Marantz AV receiver?

Yes, but with limitations. Comcast remotes can control RC5 signals; the documented codes are 0062, 0181, 0004, or 0009. However, typically only basic functions (power, volume, input) work. Advanced features usually require a dedicated universal remote or a learning remote.

What’s the difference between auto-scan and direct code entry?

Direct code entry (typing 0216, 1216, etc.) is faster and more reliable. Auto-scan loops through all available codes automatically until it finds the correct one — useful when you don’t know the code, but it can take 100+ button presses and is time-consuming.

Can I program my One For All remote to work with a Marantz receiver?

Yes. Use codes 0062, 0181, 0004, or 0009 from the One For All database. Compatible models include URC1240 (Contour 4), URC1280 (Contour 8), URC3661 (Essential 6), and URC7140 (Essence 4). Follow your remote’s manual for entering code-entry mode, and verify the code on your remote’s own sheet if one is rejected.

What should I do if my universal remote codes don’t work?

Try these steps in order: (1) test 0216, 1216, then 1296; (2) toggle AMP1/AMP2/AMP3 mode; (3) use auto-scan if available; (4) confirm the receiver is powered on and in a mode that accepts remote input; (5) verify the remote’s batteries are fresh; (6) consult your receiver’s manual for the full preset-code list.

Are Marantz TV remote codes the same as audio receiver codes?

No. Code databases maintain separate lists for Marantz TVs vs. Marantz Audio. Always verify your device type (Audio Receiver, TV, DVD, etc.) and select the matching category before entering a code.

Related Guides

• GE Universal Remote Codes
• One For All Universal Remote Codes
• RCA Universal Remote Codes
• Best AV Receiver
• Best AV Receiver Under $1000
• AV Receiver vs Soundbar

Codes and programming steps above are compiled from manufacturer preset-code manuals, established universal-remote code databases, and consistent owner reports. Where an exact value for a specific remote model could not be independently confirmed against an authoritative source, we’ve directed you to that remote’s built-in code-search rather than publish an unverified number.